User’s Manual
12 AMP Canister Vacuum Cleaner
Model: SNV12CBRB
PTT040606
SAFETY PRECAUTIONS
•
•
This vacuum cleaner should only be used for normal dry household dust and dirt.
The manufacturer cannot be held responsible for any damage caused by use of operation of the
cleaner contrary to these instructions.
•
If the cleaner is wrongly operated for a purpose other than that for which it is intended, no liability
can be accepted for any possible damage.
•
•
Do not vacuum areas which contain moisture or water and inflammable matter, needles, pins, razor
blades, matches, cigarette-ends, etc., since they may damage the cleaner or dust bag, or cause a fire.
When rewinding the cord, hold the plug body before pressing the cord rewind button to prevent
whipping.
•
•
•
Do not pull the power cord out beyond the specified length.
Make sure a dust bag and motor protection filter are always inserted.
This product includes a cable which, if damages, must be replaced by a repair shop authorized by
the manufacturer since special tools are required.
3
DESCRIPTION AND OPERATION
HOSE CONNECTION
Connecting the hose: insert hose firmly into the hose inlet.
You will hear it click into place.
Disconnecting the hose: press the button and pull the hose out
of the vacuum cleaner.
SUCTION CONTROL
The suction control at the hand grip enables you to control
suction power.
PIPE CONNECTION
Connecting the nozzle: holding the tubes and handle, insert the
narrowed section into the wide section.
WIDE SUCTION NOZZLE
Use the vacuum head for cleaning both carpeted and uncarpeted floor.
4
DESCRIPTION AND OPERATION
ON/OFF SWITCH
Press the ON/OFF switch to power on or off.
CORD REWIND BUTTON
Press the cord rewind button to rewind the power cord.
DUST METER
Change the dust bag when the dust meter displays RED.
ACCESSORY NOZZLE
Attach crevice nozzle to the end of the hose for detail cleaning.
Attach dusting brush to the end of the hose for dusting.
5
DESCRIPTION AND OPERATION
STORAGE
Hook the vacuum head to the body using the built-in clip to
store the cleaner.
PRACTICAL PARKING
Hook the vacuum head to the body using the built-in clip when
you temporarily stop vacuuming.
6
CLEANING THE FILTER
1
2
Pull out motor protection filter.
Turn off the cleaner.
Open the cover.
3
4
Shake dust out of filter and replace.
Close the cover.
Open the exhaust grill.
5
6
Pull out the exhaust filter.
Shake the dust out of the filter and
replace. Close the exhaust grill.
7
CHANGING THE DUST BAG
1
Turn off the cleaner and open the cover.
2
3
Hold the cover while removing the dust bag from the dust bag
holder.
Insert the new dust bag into the dust bag holder properly, as shown
in the picture. Close the cover.
Note: If no dust bag has been placed into the dust bag holder, the cover can not be closed.
BEFORE ASKING FOR SERVICE
Before asking for service, please check each item below if you have trouble with your cleaner.
PROBLEM
CHECK POINT
Dust bag
MEASURE
If dirt bag is dirty, replace it.
If clogged or blocked, remove object.
Suction power is weak.
Pipe or hose
Power cord
ON/OFF switch
Check if power cord is plugged in.
Check if the power is turned on.
The cleaner does not work.
Power cord does not rewind.
Pull the power cord out a little and press
the cord rewind button.
Power cord
8
© 2006 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All rights reserved.
Sunbeam® is a registered trademark of Sunbeam Products, Inc. used under license.
Distributed by Petters Consumer Brands, LLC. 4400 Baker Road, Minnetonka, MN 55343.
For service, support and warranty information, visit www.sunbeammajorappliances.com or in the US call 1-866-866-6283.
|